Categories: Linear Amplifier

400W RMS Stereo Power Amplifier


This is the schematic diagram of 400W RMS stereo power amplifier which use power transistor to work. This amplifier in addition to providing good sound power, also with excellent quality and a high fidelity with low noise, to obtain the 400 watts we can put 2 speakers of 4 Ohms or 4 of 8 Ohms. The circuit require symmetrical power supply.

400W RMS Stereo Power Amplifier Part List

Transistors:

D1047 – 4 pieces
B817E – 4 pieces
A1015 – 6 pieces
TIP41C – 4 pieces
TIP42C – 4 pieces

Resistors:

6.8 ohms – 1W (blue, gray, gold) – 4 pieces
100 ohms – 1W (brown, black, brown) – 4 pieces
18K – 1 / 2W (brown, gray, orange) – 4 pieces
1K – 1 / 2W (black brown, red) – 2 pieces
10 ohms – 1W (brown, black, black) – 4 pieces
270 ohms – 1 / 2W (red, violet, brown) – 2 pieces
10K – 1 / 2W (brown, black, orange) – 2 pieces
330 ohms – 1 / 2W (orange, orange, brown) – 2 pieces
56 ohms – 1 / 2W (green, black) – 2 pieces
27 ohms – 1W (red, violet, black) – 2 pieces
820 ohms – 1 / 2W (gray, red, brown) – 2 pieces
0.47 ohms – 5W – 8 pieces

Capacitors:

0.1uF/100v – 4 pieces
47uF/63v – 2 pieces
2.2uF/100v – 2 pieces
330pF (ceramic) – 2 pieces
4700uF/63v – 2 pieces

Miscellaneous:

Diode 1N4004 – 10 pieces
Diode P600J – 4 pieces
2 coils of 10 turns with 1/4 copper core 18.
7 amp 33x33v transformer – 2 pieces

400W RMS Stereo Power Amplifier Top PCB Design

Power Supply Schematic for 400W RMS Stereo Power Amplifier

The power supply circuit is simple, you may use 10A transformer and 6800uf of capacitor. The diode value refer to the current value from transformer and it should be have higher value. For example if you use 7A transformer, then use 10A diodes.

Input Connection with Volume Control

This is the input connection for 400W RMS stereo power amplifier with volume control using a stereo potensiometer.

circuit diagram

View Comments

  • The identification of the lower two TIP41 and TIP42 transistors is incorrect. TIP41 is the NPN device, TIP42 is PNP. The labelling of the upper two transistors is correct.

  • Please I want amplifier circuit to run horn 16 ohm 35 watt and 12-volt source is a car battery and will enclose some pictures of machine I know well I hope it's a very bad attention please.

Recent Posts

Guitar Synthesizer Schematic Diagram Collection

Guitar Synthesizer Schematic Diagram In this post, we provide a collection of schematic diagrams of…

54 years ago

Handy Talky HT DIY Schematic Diagram

Handy Talky Schematic Diagram This is an old electronic scheme of the Handy Talky (HT)…

54 years ago

Doorbell Ringer Birdie Tone

This is an old or "very old" schematic diagram of birdie tone or sound generator.…

54 years ago

200W MOSFET Amplifier based IRFP250N

Here is the 200W MOSFET amplifier powered based on four piece of IRFP250N, they are…

54 years ago

300W RMS Stereo Power Amplifier based IC TDA7294

This is the 300W RMS stereo power amplifier circuit project. This amplifier is based four…

54 years ago

Stereo Tone Control with Line In + Microphone Mixer

This is an active stereo tone control circuit using very well known op-amp IC of…

54 years ago