Categories: AudioMisc

Small Sound Amplifier for Ears (Hearing Aid)


This is the simple project of small sound amplifier for ears or often called hearing aid device or hearing loss amplifier. This circuit was already tested on some patients and give significant improvement in the hearing ability to the patients. It consumes a very small amount of power within the range of 10 milliwatts. Furthermore, the voltage Requirement of every major component is within the range of 1.8 volts and 15 volts. Therefore, for portability, a 3V DC battery is used to power the circuit.

A 32 ohms earphone is used in the output unit of this project as recommended by the manufacturers of the TDA2822M IC. According to the IC’s datasheet, this 32 ohms earphone will produce an output of about 1.3 watts. In the circuit above, capacitors C11 and C12 are called coupling capacitors. Their functions are to block any DC components in the input and outputs of the pre-amplifier. The pre-amplifier comprises of R5 and capacitor c13 which decouples the power supply of the preamplifier stage, while capacitor C12 and resistors, R2, R3 and R4 with transistor T1 forms a negative feedback amplifier which stabilizes the overall gain (A). Resistor, R4 is known as an emitter swamping resistor which also adds stability to the amplifier. The medium power amplifier amplifies the output of the pre-amplifier to an audible level. It comprises of the TDA2822M IC and those external components needed to make the IC function properly. This other external components are capacitors C14, C15, C16, C17, C18 and resistors R6 and R7. Resistor, R5 and capacitor, C13 form an RC decoupling circuit which are connected across the power supply to smooth out noise. Finally a 32 ohms earphone is used in the output unit.

Sound Amplifier for Ears : The Part List

The components used are: condensed mic, 1=2.2kΩ, 2=330kΩ, 3 = 680kΩ,12 = 33Ω,
5=10kΩ, 6 =220Ω, 7=4.7Ω, 8 =4.7Ω, , 1 =BC547A , 1 =0.01,4=100, 3 = 47, 4 = 10, 5 = 0.01 , 6 = 100, 7 = 0.1, 8 = 0.1, V1=10kΩ, LED- Red, TDA 2822M, switch and battery (3V) and earphone.
The components for the sound amplifier for ears circuit were first assembled on a bread board and tested. After it was found to work as anticipated the components were transferred to a Vero board for the final construction.

Abstract: Hearing aid device is a small electronic gadget that is fit in or behind the ear to improve one’s hearing and consequently communication ability. This research work involves the design and development of a hearing aid device with pre-amplifier; an acoustic signal picked-up using a condenser microphone. TDA 2822M IC is configured to produce an audio amplification which is converted to audio signal through a headphone. Design equations were employed to calculate the physical parameters of the circuit. After the design, the circuit was constructed and tested on 5 people with partial hearing problem. The result showed that there was a significant improvement in the hearing ability of all the patients tested. Recommendations were proposed for further improvement.

Download: Small Hearing Aid Project Document | TDA2822M Datasheet

circuit diagram

Recent Posts

Guitar Synthesizer Schematic Diagram Collection

Guitar Synthesizer Schematic Diagram In this post, we provide a collection of schematic diagrams of…

54 years ago

Handy Talky HT DIY Schematic Diagram

Handy Talky Schematic Diagram This is an old electronic scheme of the Handy Talky (HT)…

54 years ago

Doorbell Ringer Birdie Tone

This is an old or "very old" schematic diagram of birdie tone or sound generator.…

54 years ago

200W MOSFET Amplifier based IRFP250N

Here is the 200W MOSFET amplifier powered based on four piece of IRFP250N, they are…

54 years ago

300W RMS Stereo Power Amplifier based IC TDA7294

This is the 300W RMS stereo power amplifier circuit project. This amplifier is based four…

54 years ago

Stereo Tone Control with Line In + Microphone Mixer

This is an active stereo tone control circuit using very well known op-amp IC of…

54 years ago